R17 SENSOR FOR VN202 OXYGEN ANALYZER

Oxygen sensor for Vandagraph VN202 analyzers and TEK-OX models. It is also compatible with. MSA MiniOX, Dive Rite VTI, AD300 and Teledyne MD300. Jack type connection.

COMPLETE ADJUSTABLE HARNESS + KNIFE

Complete set contains of: PA harness with grommet with integrated: 2x adjustable stainless-steel buckles, 2x stainless-steel D-ring bend and 2x stainless-steel stoppers, 4 narrow and 1 wide bungees

copy of COMPLETE ADJUSTABLE HARNESS + KNIFE

Complete set contains of: PA harness with grommet with integrated: 2x adjustable stainless-steel buckles, 2x stainless-steel D-ring bend and 2x stainless-steel stoppers, 4 narrow and 1 wide bungees

R22 VAN OXYGEN SENSOR FOR DIVESOFT

vandagraph r-22van oxygen sensor for divesoft: Vandagraph R-22VAN oxygen sensor, compatible with Oxyspy. NOTE: This sensor is not suitable for use with Rebreathers

BASIC HARNESS

The WTX and WTX-D Series is a selection of harnesses, buoyancy cells and accessories which offer unparalleled versatility due to the modular nature of the whole system. Each component can be configured into a highly technical rig for those trained to push the limits, or scaled down to make a travel friendly set up suitable for any diver

BASIC DIR HARNESS

This basic harness uses 25 feet of 2 inch nylon webbing material, 3 stainless steel D-rings with weight stops are included. Two at chest level and one on the waist. Easily repositioned for optimal configuration with an OMS Stainless Steel buckle. A 2 inch sewn crotch strap with a 2 inch Scooter “D” ring is also included. This harness is available to be installed on a diver’s backplate or on the OMS Aluminum or Stainless Steel backplates. Divers that prefer the simplest, most utilitarian harness generally choose this configuration. Available as a Kit or installed on OMS Backplates

R22AT OXYGEN SENSOR FOR ATA

r-22at vandagraph oxygen sensor for ata: R-22AT Vandagraph oxygen sensor compatible with: Analox ATA, Analox ATA Pro, Analox 9100-9212-94

ELITE 2 HARNESS

Tech/Rec is at its best with the Elite 2 Harness. The Elite 2 Harness System offers you all the features of a technical harness with the added comfort that recreational divers look for.

SOLO HARNESS

Designed to meet all the needs of demanding technical divers, the Solo Harness System is clean, simple, and foolproof!

BLACK WEIGHT POCKET 2.3 KG UNIT

High resistance cordura weight pocket for harness, with capacity for 2.3 kg ballast pads approximately. Fast closing and release clip in plastic on the outside and flap with Velcro. Ideal to place on harness webbing, tank webbing and even on belts. Stainless steel eyelet at the bottom for water drainage and rear strap to adjust to bottle buckle or harness. Sold by the unit.

ACCESSORIES POCKET BLACK

Heavy duty cordura accessory holder pocket for harness or jacket, perfect for carrying small accessories and even a spare mask . Ideal to place on harness webbing, jacket and even on belts with webbing up to 50 mm.

XTREM KANGAROO SMALL HANDBAG

The TDS Xtrem Kangaroo pocket is a pocket specially designed for technical diving, being valid for both backmount and sidemount systems thanks to the versatility of its design. A pocket designed to the smallest detail to offer maximum performance to the technical diver.

TRIM WEIGHT POCKET

Designed to be mounted on 2 inch webbing, vertically or horizontally. Can be used on nylon tank bands to augment the divers trim.

ARMADILLO BACK PAD

Additional rear part of backplate for attaching the sidemount bottles.Material: Cordura 1100, webbing, stainless-steel AISI 316. Weight: 0,28 kg

ADITIONAL POCKET

Additional pocket for backplate ballast system or belt. Dimensions 18x15x4 cm

BACK PLATE POCKET

Designed for placing a buoy or a lifting bag between the backplate and diver´s back. Stainless-steel screws for attaching the pocket to the backplate are included.